SanDisk-Toshiba Take Back The Crown With A Different Kind of NAND
by Jason Inofuentes on May 5, 2011 12:01 PM ESTAfter 11 years of partnership, Sandisk and Toshiba's timing could not have been better. Just seven days after losing the NAND crown to Intel and Micron (IMFT) they announce they will have 19nm NAND samples rolling off their fabs as we speak. This one upmanship is normal for this industry but the announcement coming so soon after IMFT's 20nm announcement was a surprise to many. Like IMFT, they expect to start mass production during the second half of this year, and finding homes for their latest NAND in the next wave of tablets, smartphones and SSDs.
Toshiba NAND on display on the Kingston SSDNow V+100
Anand and I had the opportunity to speak with representatives from Toshiba and SanDisk who sounded quite optimistic about the competitiveness of their 19nm products. Like IMFT, they expect to see similar endurance as their 24nm products, around 3,000 program/erase cycles. This is owing to ever improving ECC and wear leveling algorithms, ensuring as few wasted p/e cycles as possible. SanDisk and Toshiba did not publish die size for this iteration, but did state a decrease of approximately 25%. Previously, their 24nm die size was published as 151mm2, so this iteration should bring that down to about 113mm2, besting IMFT's 118mm2 at 20nm. Page and block sizes remain at their 24nm levels of 8 KB per page and 256 pages per block.
While the benefits for SSDs are the main focus of our NAND coverage, consumer electronics are where the vast majority of readers interact with NAND products. Flash memory is a key component of smartphones, tablets, media players and set-top boxes, in addition to the USB drives and memory cards. Different calibers of NAND are used in these products, with the fastest (SLC) going into enterprise-class SSDs, the mainstream NAND (2-bit MLC) going into your consumer and enthusiast SSDs, phones and tablets and slower products (3-bit TLC and 4-bit 16LC) going into products like jump drives and SD cards. Drawing from Anand's SSD Anthology we recall that the functional difference between SLC and MLC is the amount of data per NAND cell, 1-bit or 2-bits. Adding that extra bit to SLC to make MLC decreases speed and reliability; the same holds true in producing 3-bit NAND. With controllers and ECC algorithms improving, it is likely that 3-bit NAND will be produced in this venture that will end up in more consumer electronics devices, perhaps not your next SSD, but certainly some tablets and smart phones (note that there are 3-bit SSDs floating around in beta form). The benefit for consumers is larger capacity with little price increase and relatively little impact on performance and reliability since consumer electronics devices rarely tax the limits of NAND speed and are designed to endure less than even a conservative estimate for how long the NAND inside should last.
Within the consumer electronics space, however, NAND can be configured in various ways. Above is a block diagram of your average SSD; SATA interface leads to the Controller which uses DRAM to coordinate operations and reads/writes to/from the supply of MLC NAND. Some consumer electronics devices use this exact configuration, as in the Acer Iconia W500 windows tablet. In other devices a similar configuration is used but in an embedded format, where controller and NAND are in a single package soldered to the device's PCB. Still others use raw NAND and utilize the device's own silicon to read/write to the NAND itself, as in all iOS devices. In nearly all of these configurations, volatile memory (DRAM) is used as cache for pending operations (Intel and SandForce excluded, they cache in SRAM); which means that a sudden loss of power could lead to the loss of data that had been waiting to be written to NAND. SanDisk-Toshiba NAND has learned a new trick, apparently present even in the currently shipping 24nm products, that eliminates this risk while also adding a few new options for OEMs.
In the block diagram above, gleaned from SanDisk marketing and discussions, DRAM is abandoned in favor of designating a portion of NAND as cache. Data is stored here initially, to be written to MLC during time the controller would otherwise be idle. This area designated as cache isn't just regular MLC NAND, however; it's what was described to us as "pseudo-SLC," treated at the hardware level like SLC but with the narrow voltage deltas of MLC. The benefits are obvious, an increase in speed and reliability, the former of which should mitigate any speed lost from not using SDRAM. Further it seems this pseudo-SLC feature can be used to fill other roles. In its iSSD products, intended for larger consumer electronics devices, SanDisk uses this pseudo-SLC NAND as in the diagram above. A conversation with Toshiba, however, revealed that other OEMs will use psuedo-SLC as speedy reliable storage for firmware (OS) and system files. The technology is manipulated at the block level, and with each block's capacity halved by treating it as SLC, OEMs have a 1MB granularity with which to designate this SLC space for use as cache or as an OS partition.
In their respective press releases, SanDisk and Toshiba both highlight the smartphone and tablet spaces as motivating factors in their drive towards smaller process nodes. Indeed this has been the focus of much of their marketing of late. Their innovations in ECC and this pseudo-SLC technology are tailor made for this space and though no specific devices were named, we are no doubt benefiting from their implementation already.
The iPad 2 Mainboard featuring Toshiba NAND, courtesy of iFixit
There are costs to this approach, the main one being . . . well, cost. DRAM is cheap relative to NAND, so sacrificing several blocks of NAND is more expensive than adding 512MB of RAM. Further, though faster than MLC, the writes to SLC NAND are slower than they would be to SDRAM, so a performance penalty is paid. With cost and speed being the driving factors in the consumer SSD space, SanDisk-Toshiba's new trick seems ill suited to the PC space. Enterprise-class SSDs could benefit from the data resilience but these applications are typically laden with power redundancies that provide their SSDs sufficient power to complete any pending writes before losing power. Only in the consumer electronics space is there a strong and growing market for just fast enough, incredibly reliable NAND.
35 Comments
View All Comments
RU482 - Tuesday, May 10, 2011 - link
As NAND die sizes shrink, does temperature have a greater or lesser effect on the life and performance of the circuit?To put it another way, would a 19nm NAND be more or less stressed by temperature when compared to a 25nm or 32nm NAND?
flyvog6 - Tuesday, May 17, 2011 - link
sells clothing,footwear,handbags,SunglassesOnline Store,Get Name Brand Fashion From 12USD Now!
Our Website: ===== www voguecatch com ====
Our main product list is as follows:
flyvog6 - Tuesday, May 17, 2011 - link
sells clothing,footwear,handbags,Sunglasses
Online Store,Get Name Brand Fashion From 12USD Now!
Our Website: ===== www. flyingstyle org ====
Our main product list is as follows:
aa0101bb - Wednesday, May 18, 2011 - link
sells clothing,footwear,handbags,SunglassesOnline Store,Get Name Brand Fashion From 12USD Now!
Our Website: ===== the web w w w voguecatch com ====
Our main product list is as follows:
runeks - Monday, June 13, 2011 - link
Would be cool to see some benchmarks of this. I suspect it's the iSSD that is used in the Efika MX Smarttop and Smartbook. They have 8GB and 16GB, respectively. But I haven't gotten hold of any benchmarks yet (random read/write). Sandisk website says it's 160 MB/s, 100 MB/s sequential read/write, respectively.